Search results

Is it possible to move my 292 L6 forward? I heard the motor mounts are different for it than the V engines? I think that would place my new trans shifter in the old hole. Thanks Matt

Thanks, Val. The shifter is probably 3" or so farther back than the original, so I hope it won't be that big an issue. The e brake will probably take the most attention. I'll keep you guys posted. Matt

I recently acquired a newly reman 5 speed out of a 97 1500 and want to put it in my 65 to replace my old 4 speed. Don't know if any of you have tried something like that. It looks like I will have to remove the e brake crossmember to make it fit and the trans crossmember mounts toward the...

Those look just like the ones i used on my 65. I am not real big on that gap, but mine are bolted in just like that. I had a heck of a time but I was able to get them flush using a ball joint press. Enjoy, Matt

Looking for a power steering pump bracket for my 65 c10 w/ L6 292. Appreciate any any advice. Thanks, Matt

I have a 65 C10 2wd and am looking to swap to a 4wd frame. I found a 1983 K20 suburban donor but unsure of total length of it. The info I found said the wheelbases were almost the same and I know I'll have to fabricate the mounts. What do you think? Also I went to go rent a tractor on a...

Wanting to go with power steering but am having trouble finding a PS pump that will mount on to my straight 6 292. Will any later model chevy PS set ups work with what I have? Thanks, Matt

My 65 c10 has a 4 speed manual trans. I don't currently have reverse lights but was wanting them. Can they be added to my truck and how? Thanks, Matt

You guys are great! I will look into these and try to get some new pics posted.

Hey, guys, been gone for a while but am back after it. I just had my straight six rebuilt and now I'm ready to travel. I know most guys want to go bigger but I just like that lil six. I would like to move the gas tank to the rear and was wondering if there were used ones out there (what...

I just got my lady back on the road after my "custom mix and match" front disc upgrade (if I'd found you guys before I started buying parts you could have saved me several headaches by getting a kit). Put new wheels and tires on her and she looks to be coming to life finally. Problem is that...

My old exhaust pipe is run under all the crossmembers and each place is pretty crimped down from bottoming out. Will this cause problems until I can get it fixed? Also right now I have a 292 L6 w/ manual transmission. I want to eventually get a 350 V8 and auto trans. If I redo the exhaust...

About ready to get her back on the road, and had a little question for you guys. My current heater/fan switch is a pull knob. I have seen a console w/ the three levers and was wondering if the two were interchangeable. The lever one has three cables it looks like and mine has only one...

I have some interests. Give me a shout at [email protected]. Thanks, Matt.

Doing the same thing w/ my 65. Going w/ Early Classics for the rotors in front. Having to use 71-87 tie rod ends as well since my old 65 ends are not long enough for the bolt to go through the spindle arm. A question for you guys--will the 71-87 inner tie rod end fit through my 65 tie rod? I...

Val, I think you saved my life, but I can't say as much for my undies. That first pop got my attention real quick. Got the spindles off though. Turns out both my front springs were broken as well. Just more to add to the wish list. Appreciate all the advice, and I'm sure I'll be back for...

Doing disc brake swap on my 65. This leaves me with 5 lug on front and 6 lug in back. What is the easiest way to convert the rear axle so they will be the same. Do I want to put disc on the rear as well? PS How do you have to pry to get those old ball joints out. I'd hate to hurt my...

Does it matter what make/model of posi trac rear axle I put on my truck. Found several but don't know if they would fit on my truck. Also, call me clueless but what does the gear ratio mean and what's the best one to use? Thanks for the advice. One of these days I might actually know...

Hey guys, Jeffery has a 68 4x4 for me. I was wondering if the frame lengths, cab/bed mounts, and bumper mounts are the same. Does anyone know? Thanks, Matt.

Recently bought 65 lwb stepside 2wd and interested in converting to 4wd. Looking for solid frame and working 4wd equipment. You guys are great! Thanks, Matt.