What should I use for a gas tank?

Discussion in '1947-1954' started by Bill Hanlon, May 22, 2013.

  1. Bill Hanlon

    Bill Hanlon Member

    Joined:
    Jun 4, 2002
    Messages:
    2,744
    Location:
    Fredericksburg TX
    '52 GMC 150 with a flat bed. I'm 6'5" and would like more leg room. I'm shopping for a replacement seat and have tried out a fellow old trucker's 54 Chevy with a 2003 Chevy Astro Van 2nd row seat mounted to the original adjusters with two custom brackets. This arrangement yields 2.5" additional room between the firewall and the seat back as well as 2" more room between the seat and the roof. But the gas tank needs to leave the cab to have this additional space.

    I'd like to mount the new tank under the front edge of the bed on the passenger's side

    One option would involve a tank with max dimensions of 18" front to rear, 12" left to right and 17" deep. Max of about 16 gallons.

    Another option would have max tank measurements of 26" front to rear, 27" left to right and 11" deep. This arrangement would need a heat shield near the muffler. Max of about 33 gallons.

    The third option would have max tank measurements of 26" front to rear, 19" left to right and 11" deep. Max of about 23 gallons.

    All of these would be simple rectangular tanks. I'd run the filler out the right side and leave it under the edge of the bed.

    I've looked at Tanks, Inc. without much luck so far.

    Any of you have experience in this field?
     
  2. ccharr

    ccharr Member

    Joined:
    Jun 7, 2006
    Messages:
    2,175
    Location:
    Simi Valley, Ca. , La Paz County, Az.
  3. 52wasp

    52wasp Member

    Joined:
    Jul 21, 2006
    Messages:
    674
    Location:
    Wilton, New Hampshire
    Bill,
    Try an S10 tank (part number GM16D).
     
  4. Bill Hanlon

    Bill Hanlon Member

    Joined:
    Jun 4, 2002
    Messages:
    2,744
    Location:
    Fredericksburg TX
    Charles: What mounting hardware is needed and where does it attach to the truck when using the 47/48 tank?
     
  5. ccharr

    ccharr Member

    Joined:
    Jun 7, 2006
    Messages:
    2,175
    Location:
    Simi Valley, Ca. , La Paz County, Az.
    Bill,

    The hardware bolts to the frame and has steel straps that go around it & tighten up on it.
    Joe should have the hardware for the 47/48 models, he may even have a good tank also. Give him a PM to see.
    I'll post the frame I'm redoing to put the extra tank on mine.
     

    Attached Files:

  6. Bill Hanlon

    Bill Hanlon Member

    Joined:
    Jun 4, 2002
    Messages:
    2,744
    Location:
    Fredericksburg TX
    Thanks for the pictures Charles. I assume that the bracket in your picture would be mounted to the truck with just one bolt at the top of the "step" area of the bracket. Correct? If so, where does the bracket attach to the truck? Approximately what is the dimensions top to bottom and side to side of the bracket?

    Bill
     
  7. ccharr

    ccharr Member

    Joined:
    Jun 7, 2006
    Messages:
    2,175
    Location:
    Simi Valley, Ca. , La Paz County, Az.
    One bolt, yes. It connects to the inside of the frame. close to the E-Brake gizmo's for those yr. trucks. See photo attached below. The measurements for the bracket are 3.5 in. top at frame, next hump is aprox 7 in. then to the top angles up is 8.5 in. where the unit bolts the strap together, next hump area is aprox 11.5 in.from the 8.5 in level to the outside strap is aprox. 13 in. hope this helps, I do not have the truck here or I would take more photos for you.



    Charles
     

    Attached Files:

    Last edited: May 23, 2013
  8. Flashlight

    Flashlight Member

    Joined:
    Apr 6, 2009
    Messages:
    676
    Location:
    Greeneville, Tennessee....Looking out over the Smo
    The 47-48' pick-up tank mounts there and also the same or similar tanks were used on the panel trucks for some years later as they didn't have space behind the seats. It opens up your search options a bit.
     
  9. SinclairChevy

    SinclairChevy Member

    Joined:
    Dec 18, 2011
    Messages:
    590
    Location:
    Keokuk, Iowa
    Love this thread. I'm planning on putting my tank where Bill wants to as well. Always looking for options. Thanks for posting the question, Bill!! I hope you find what you're looking for.

    Damon
     
  10. Larrys 48

    Larrys 48 Member

    Joined:
    Dec 7, 2007
    Messages:
    617
    Location:
    Spokane, WA
    '48 tank

    Bill,
    I think Jim Carter has started selling the replacement support hardware.
     

    Attached Files:

  11. vwnate1

    vwnate1 Member

    Joined:
    Jan 1, 2000
    Messages:
    11,673
    Location:
    AMERICA !
    Fuel Tank

    Ahead of the rear axle for safety's sake ~ dying in a blazing fire sux .

    As Gasoline isn't .25 CENTS anymore , I'd be wanting to try and mount the filler neck on the driver's side , if not the whole tank .

    I highly concur with the suggestion you buy a good used '47 or Panel Truck tank & hardware from Joe and have Gas Tank Renew U.S.A. do their thing to it before installation .

    Even if you buy a brandy new tank , do this as new tanks are made of tin foil and have pinch weld leaks 50 % of the time right out of the box .

    I see Charles cleverly showed off his vintage equipments in the first set of photos :rolleyes: .

    The electric fuel pump frame mounted close as possible to the tank is smart too .

    Did I mention how , when you're in a fire , you don't actually burn to death , rather , the flames burn you so badly you open your mouth to scream and inhale the 2,000? F flames and fumes , this dissolves the bronchial tubes in your lungs so you suffocate , feeling the flames roasting your body at the same time , as you can't get any air in you can't scream and so on .

    Add to this the need for a closed casket in every case and the Gas Tank Renew U.S.A. deal becomes a whole lot more palatable .

    SAFETY KNOWS NO SEASON ! .
     

Share This Page