Search Results

Search Again
Page 7 of 10
  1. Bobby 57
    Post

    Bed

    I machined the wood myself . I changed the the dimensions of the planks to be equal widths using 7 planks instead of 8 .With a table saw and a...
    Post by: Bobby 57, Dec 28, 2010 in forum: 1955-1959
  2. Bobby 57
    Post

    FOUND 3.38 gears on ebay for $199

    where in Ca, are you?
    Post by: Bobby 57, Dec 26, 2010 in forum: 1955-1959
  3. Bobby 57
    Post

    59 Apache Door Seals

    what you need is a warm day,move the strike in the distance of of the door in. let the seal get warm then close the door and let it set.you may...
    Post by: Bobby 57, Dec 26, 2010 in forum: 1955-1959
  4. Bobby 57
    Post

    59 Apache Door Seals

    it looks like the rubber is holding it out is that correct?
    Post by: Bobby 57, Dec 26, 2010 in forum: 1955-1959
  5. Bobby 57
    Post

    59 Apache Door Seals

    send a picture showing where the gap is at. You made need to tweek the door a little bit. I had to do that with mine. it did take much. Bobby
    Post by: Bobby 57, Dec 26, 2010 in forum: 1955-1959
  6. Bobby 57
    Post

    59 Apache Door Seals

    is the 1/2" gap interior or exterior ? the reveal (gap) on the exterior on my 57 is an 1/8" and that dictated the interior reveal and the door...
    Post by: Bobby 57, Dec 25, 2010 in forum: 1955-1959
  7. Bobby 57
    Post

    power brake update in a 46 1/2 ton

    Nice job on the plumbing.very clean.keep up the good work. Bobby
    Post by: Bobby 57, Dec 15, 2010 in forum: 1947-1954
  8. Bobby 57
    Post

    $%&% Soft Brake Pedal

    when you pump the pedal to bleed the system.How fast are you pumping the pedal? If you pump too fast you airate the brake fluid which puts air...
    Post by: Bobby 57, Dec 15, 2010 in forum: 1947-1954
  9. Bobby 57
    Post

    Midwest blizzard

    I was sittin' in a treestand in Putnam county/northern Missouri.The snow wasn't to bad but Sunday and Monday the temp was 5 degrees with a wind...
    Post by: Bobby 57, Dec 15, 2010 in forum: 1947-1954
  10. Bobby 57
    Post

    Body panels’ alignment

    core support,inner fenders,fenders,lower grill support, upper grill support with hood latch,hood springs,and hood. I'm not a body man ,but thats...
    Post by: Bobby 57, Nov 10, 2010 in forum: 1955-1959
  11. Bobby 57
    Post

    1955 Gas tank under the Bed Conversion

    I did this conversion to my 57.I hope the pics help. Bobby
    Post by: Bobby 57, Nov 10, 2010 in forum: 1955-1959
  12. Bobby 57
    Post

    Where do you begin to fix the boards?

    I did mine on my 57.I didn't buy the kit because i changed the layout of the boards from 8 boards to 7.Its not that hard to do measure twice cut...
    Post by: Bobby 57, Nov 7, 2010 in forum: 1947-1954
  13. Bobby 57
    Post

    Bad vibes

    I like that link.explains things very well.-2 wasn't enough,-4 was perfect.A lot of trial and error to find what felt good.Thanks again for the...
    Post by: Bobby 57, Oct 15, 2010 in forum: 1947-1954
  14. Bobby 57
    Post

    Bad vibes

    check your pinion angle with an inclinater.If its 4or 5 degrees you should be fine. Bobby
    Post by: Bobby 57, Oct 15, 2010 in forum: 1947-1954
  15. Bobby 57
    Post

    Bad vibes

    1) Did you over tighten the u-bolts nuts on the u-joint? 2) How long is the drive shaft now? 3) whats the diameter?4) is the drive shaft and...
    Post by: Bobby 57, Oct 14, 2010 in forum: 1947-1954
  16. Bobby 57
    Post

    55-59 C-notch

    But when you modifications like that they stand out nice when powder coated and you feel good with the compliments that come with it. Bobby
    Post by: Bobby 57, Oct 14, 2010 in forum: 1955-1959
  17. Bobby 57
    Post

    1958 Chevy w/napco 4by4

    Nice ride.Thanx for the pics. Bobby
    Post by: Bobby 57, Oct 5, 2010 in forum: 1955-1959
  18. Bobby 57
    Post

    51 Front Shock Questions

    1) the steep angle is normal per application.Shock angle wasn't important then like it is now.Shocks now days work better when there straight up...
    Post by: Bobby 57, Oct 5, 2010 in forum: 1947-1954
  19. Bobby 57
    Post

    Pictures worth a 1000 words

    Thanks.Yes i did. I have access to a shear and brake. Welded together.then used nut-serts and cap screws to bolt it to the floor..Even though the...
    Post by: Bobby 57, Oct 2, 2010 in forum: 1955-1959
  20. Bobby 57
    Post

    Pictures worth a 1000 words

    Thanks.The AC is from Old Air Inc. out of Texas.Good customer service sold me on there product. Bobby
    Post by: Bobby 57, Sep 28, 2010 in forum: 1955-1959
Showing results 121 to 140 of 195 Next >
Search Again
Page 7 of 10