Search results

I read about this upgrade on ck5.com about 2 years ago and finally got around to trying it this week. I've tried just about everything else: cleaning/lubing tracks, new motors, and even replacing the regulators with new ones from Classic Parts; but this has been by far the biggest improvement...

Has anyone here rebuilt their power steering pump? I'm wondering how hard this is and if there are any tricks I should know before I take mine apart. My hydroboost system has always had the common seeping problem, but lately it seems to have gotten a little worse. I ordered a new set of AC...

I have a pair of seats from an '87 Suburban I want to put in my truck. The seats are blue (velour w/ vinyl back) and my interior is black. There are no rips or tears, only the padding in two of the armrests needs to be replaced. I just spent a lot of money converting my truck to a diesel, so...

Has anyone taken apart or know how to take apart seat tracks? I bought some bucket seats from an '87 K20 Suburban to put in my C10. I also got the tabs for the front inner corners of the seats. But the problem I've found is that the tracks are different in the rear. The Burb's tracks...

I bought a center console from a '82 Blazer to put in my truck when I install bucket seats. I've taken apart standard latches on glove boxes, but this is the first locking one I've dealt with. I dont have the key, which I've heard is needed to remove the latch. Anyone know if this is true...

[updated:LAST EDITED ON Jul-11-05 AT 02:36 PM (CST)]I just upgraded my C10 to 3/4 ton, now I need to clean up the yard. 10 bolt w/ 3.08's, 190K, never given me any trouble $40 I also have upper and lower a-arms, steering knuckles, coil springs, (everything but the rear springs and brake...

I just bought a pair of old door panels so I could upgrade my truck to power windows/door locks. The only problem is that the panels are grey, whereas the rest of my interior is black. I bought some vinyl paint, cleaned them with some diluted detergent (as the paint reccommends) and painted...

I had my carb rebuilt recently and now my truck is having trouble in the mornings. The engine runs smoothly until I put it into gear, if I dont give it some gas it will stall and it has trouble accelerating. I already took it to my mechanic once to adjust the choke, but now that I'm going back...

I bought an axle off a '77 Chevy and I need to convert my e-brake to the older style (down either side of the frame). Im looking for pretty much everything except the rear cables and the pedal (this includes brackets). Thanks, Craig

I need to replace the driveshaft bearing on my truck. I know I need to take the driveshaft into a machine shop to get it pressed on, but how do I remove it? I've taken off the rear piece, but it still has the molded plastic retainer type U-joints on the front section. Would it be possible to...

I bought a 14b ff axle at the junkyard recently and just checked the backlash, which is about .013-.014in. How do I adjust the ring gear to lower the backlash?

i'm planning to replace my 5 lug 10 bolt rear with a 8 lug 14 bolt FF axle over the summer. What's the cheapest way to convert the front end to 8 lugs? Is there any difference between the spindle on my truck and a C20? (I know the wheel bearings and ball joints are different) I looked in the...

I was wondering if Chevy Duty sells the fan shroud for a 4.3L engine. Looking in your catalog I didn't see any that matched what I am looking for, a 2-piece 6 cylinder. I need the upper half (mine's on duct-tape life support::7 ). thanks, Craig

I've been looking into rebuilding the carbuerator on my truck, so I emailed a company called carbs only for info/ a kit. Only they told me they couldn't find a rebuild kit for my carb (17083502) even though they had the carb # listed, and that not even AC Delco makes a kit for it. x( They...

I recently bought some leaf springs off a junked '75 3/4 ton chevy for my '85 C10. They look to be in pretty good shape but I still need to replace the old rubber bushings with some new poly bushings. I'm wondering what's the best way to remove the old bushings?